Datalogic Reader Matrix-1000 Bedienungsanleitung PDF herunterladen (Seite 2)

MOUNTING Matrix 400™

The following parts are required for mounting:

 LT-100 Cone Lighting System

 BK-4990 Matrix 400™ Generic LT Bracket

1. The BK-4990 bracket comes already partially mounted (D+A) with

2 M4 screws.

2. Mount the bracket A onto the LT-100 Cone B using the 4 M2.5

screws in the bag marked "Screws for Brackets-LT-100/LT-300

assembling".

3. Swing the bracket D 90° and mount the reader C onto it through

the mounting holes on the bracket. Use 4 of the M4 screws in the

bag marked "Screws for Bracket-Bracket-Reader assembling".

4. Wire the LT-100 to the CBX according to the following Wiring table.

5. Remove the Lens Cover and loosen the Locking Knobs as

described in the Reference Manual. Swing the bracket D 90°

returning to the reading position.

6. Position and mount the Matrix assembly over the code reading

area at the correct Focus Distance (or range) for your model,

(described in the Matrix Reference Manual).

7. Perform the Focusing procedure described in the Reference

Manual.

8. After Focusing, tighten the Focus and Diaphragm Locking Knobs.

Swing the bracket D 90° as previously shown to replace the Lens

Cover. Swing the bracket D 90° returning to the reading position

and fix the reader assembly (C+D) to the illuminator assembly

(A+B) with the remaining 2 M4 screws from the bag marked

"Screws for Bracket-Bracket-Reader assembling".

POSITIONING Matrix 400™

code surface

Focus distance = α + β

The best results for this illuminator are obtained when α is

approximately 20 mm (0.8"). However other Reading Distances

(described in the Matrix Reference Manual) can be used. You can

maximize the reading performance through VisiSet™.

WIRING

Wire Color CBX/Matrix Signal Meaning

Red Vdc 10 to 30 Vdc

Black GND Ground

Blue O1-, O2-, (O3-) Control Signal -

White O1+, O2+, (O3+) Control Signal +

CAUTION

The LT-100 control signals must always be

connected to one of the Matrix Digital Output

signals. In VisiSet™, set the relative Output Line

Function parameter to "External Lighting System" and

the Matrix Output x External Lighting System Mode

parameter to "Triggered".

TECHNICAL FEATURES

Supply Voltage 10 to 30 Vdc

Power Consumption 1.5 to 0.5 A; 15 W max.

Optimal Working Distance 20 mm (0.8")

Effective Working Range 12.7 - 50 mm (0.5" - 2")

Illumination Area Ø 90 mm @ 20 mm

(Ø 3.5" @ 0.8")

Wavelength 630 nm

Max. LED Output Power 0.2 mW to EN60825-1

Typical Irradiance 10 W/m² @ 20 mm

Operating Temperature 0 – 40 °C

Dimensions (D x H) 140 x 58 mm (5.5" x 2.3")

(without bracket)

Weight 305 g. (without bracket)

COMPLIANCE

LED Class

Class 1 LED Product to EN 60825-1:(2001)

Power Supply

This product is intended to be connected to a UL Listed Direct Plug-in Power Unit

marked LPS or “Class 2”, rated 10 to 30 V, minimum 1.5 A.

CE Compliance

Warning: This is a Class A product. In a domestic environment this product may

cause radio interference in which case the user may be required to take adequate

measures.

FCC Compliance

Modifications or changes to this equipment without the expressed written approval

of Datalogic could void the authority to use the equipment.

This device complies with PART 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference which

may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

821000893 (Rev. G)

40 mm

1 2

Kommentare zu diesen Handbüchern

Keine Kommentare

Datalogic Reader Matrix-1000 Bedienungsanleitung Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Vernetzung Datalogic Reader Matrix-1000