Datalogic DL Cordless Card DLCC Bedienungsanleitung

DL TCL™User’s Manual

DL TCL™ 4 2 Once the communication between the terminal and DL Mobile Configurator™ Enterprise 2 has been enabled, it is possible to start the downl

CONFIGURING THROUGH DL MOBILE CONFIGURATOR™ ENTERPRISE 2 5 3 3 CONFIGURING FROM DL MOBILE CONFIGURATOR™ By selecting the DL TCL™ item in the Sele

DL TCL™ 6 3 3.1 DEVICE It allows defining the main parameters of the terminal: Figure 6 – Device Parameters Beep Duration It defines the beep du

CONFIGURING THROUGH DL MOBILE CONFIGURATOR™ ENTERPRISE 2 7 3 3.2 CONNECTION It allows configuring the connection between the application and the r

DL TCL™ 8 3 3.3 EMULATION It allows defining the emulation parameters: Figure 8 – Emulation Parameters Device Name It defines the name of the te

CONFIGURING THROUGH DL MOBILE CONFIGURATOR™ ENTERPRISE 2 9 3 Del to BS It enables/disables the delete command when pressing the Backspace (BS) key o

DL TCL™ 10 3 3.4 ADVANCED It allows to configure the advanced configuration features: Figure 9 – Advanced Parameters Start Row It defines the li

CONFIGURING THROUGH DL MOBILE CONFIGURATOR™ ENTERPRISE 2 11 3 3.5 DISPLAY It allows configuring the font type for the application. Figure 10 – D

DL TCL™ 12 3 Scrolling Modes Fixed The terminal display is always locked at column 0 and row 0. Quadrant Mode The entire host screen (80x25) is div

CONFIGURING THROUGH DL MOBILE CONFIGURATOR™ ENTERPRISE 2 13 3 3.6 BARCODE DATA ENTRY It allows configuring the entry of barcode data. Figure 11

DL TCL™ 14 3 Clear Before Scan This special key is only available in connection with an AS400 host. If checked, it clears the input field before sen

CONFIGURING THROUGH DL MOBILE CONFIGURATOR™ ENTERPRISE 2 15 3 Mode If set to Recognition Only, it allows editing a single input filtering mask to se

DL TCL™ 16 3 3.7 PRINTER It allows configuring the printer. Figure 14 – Printer Setting Communication It defines the port to be used to send dat

CONFIGURING THROUGH DL MOBILE CONFIGURATOR™ ENTERPRISE 2 17 3 Stop Bits It indicates the number of stop bits the data packet of the communication pr

DL TCL™ 18 3 3.8.1 General Parameters Code Length It defines the minimum and maximum length of the code to be read. Figure 16 – Code Length Rea

CONFIGURING THROUGH DL MOBILE CONFIGURATOR™ ENTERPRISE 2 19 3 Preamble/Postamble It defines the preamble and postamble characters using the ASCII de

DL TCL™ 20 3 Always On : if checked, it allows the scanner to read even if the DS function has not been called (for diagnostic purpose only). SW Con

CONFIGURING THROUGH DL MOBILE CONFIGURATOR™ ENTERPRISE 2 21 3 3.8.2 Linear Codes The Linear Codes branch lists all the code symbologies which can b

DL TCL™ 22 3 3.8.3 2D Codes If configuring a terminal supporting the SE2223 driver, it is possible to read 2D codes. Figure 24 – 2D Code Selecti

CONFIGURING THROUGH DL MOBILE CONFIGURATOR™ ENTERPRISE 2 23 3 3.9 HOSTS It allows defining the configuration of up to 5 Hosts to which DL TC™ can b

DL TCL™ USER'S MANUAL

DL TCL™ 24 3 Host Profile It defines the logical name to be assigned to the current Host. Host Name / IP It defines the address to be used by the t

CONFIGURING THROUGH DL MOBILE CONFIGURATOR™ ENTERPRISE 2 25 3 The button available on the program Tool bar allows deleting the selected Host from

DL TCL™ 26 3 The table next to the keyboard graphical layout list all the defined key mappings. In particular, the “Virtual Sequence” column shows t

CONFIGURING THROUGH DL MOBILE CONFIGURATOR™ ENTERPRISE 2 27 3 Then, click on the Next button to define the mapping terminal key. In this case, whene

DL TCL™ 28 3 Setting the Exit Emulation Key The Exit Emulation Key is a special key allowing to exit the terminal emulation application. For this r

DL TCL™ EXTENDED COMMANDS 29 4 4 CONFIGURING FROM TERMINAL Once the DL TCL™ application and configuration files have been downloaded onto the ter

DL TCL™ 30 4 4.1 MAIN SETUP MENU At terminal boot, the following opening mask is displayed: Datalogic Spa DL - TCL Terminal Emulation ESC to

DL TCL™ EXTENDED COMMANDS 31 4 As described in the introduction of this chapter, press the numeric key corresponding to the number next to each opti

DL TCL™ 32 4 4.2.1 TCP/IP If selecting this submenu, the following masks appear allowing to define the IP parameters related to the terminal. &q

DL TCL™ EXTENDED COMMANDS 33 4 The IP Address value must respect the xxx.yyy.www.zzz structure, where x, y, w and z value is in the range 0-255. Aft

DATALOGIC S.p.A. Via Candini 2 40012 - Lippo di Calderara di Reno Bologna - Italy DL TCL™ This manual refers to software version 4.0 and lat

DL TCL™ 34 4  DNS The definition of the DNS IP address must respect the xxx.yyy.www.zzz structure, where x, y, w and z are in the range 0-255:

DL TCL™ EXTENDED COMMANDS 35 4 4.2.2 Radio This submenu allows selecting the radio network the terminal belongs to. The selected parameter acts upo

DL TCL™ 36 4  Open Air Radio Datalogic - SETUP Network Radio 1) Open Air 2) IEEE 802.11b 3) IEEE 802.11 ENTER to Continue Datalogic - SETUP Open

DL TCL™ EXTENDED COMMANDS 37 4  IEEE802.11b Radio Datalogic - SETUP Network Radio 1) Open Air 2) IEEE 802.11b 3) IEEE 802.11 ENTER to Continue I

DL TCL™ 38 4 When configuring the radio, the "Out of Range" option (set [AUTO]) allows DL TCL™ to automatically signal if during data tran

DL TCL™ EXTENDED COMMANDS 39 4  IEEE802.11 Radio Datalogic - SETUP Network Radio 1) Open Air 2) IEEE 802.11b 3) IEEE 802.11 ENTER to Continue Da

DL TCL™ 40 4  Host If configuring the Host PC, the communication will automatically enter the Direct Host Mode (see par. 1.1.1 for details). Dat

DL TCL™ EXTENDED COMMANDS 41 4 The management of this feature depends on the selection of the Multi-Session parameter: - Single Session: the Multi

DL TCL™ 42 4 4.3 EMULATION MENU This menu allows setting the parameters managing the terminal emulation: Datalogic - SETUP Emulation 1) General

DL TCL™ EXTENDED COMMANDS 43 4  KeepAlive Timeout It defines the time interval (in seconds) between the transmission of two NOP packets.  DL TC

iii CONTENTS 1 GENERAL INFORMATION ... 1 1.1 DL TCL™...

DL TCL™ 44 4  Local Echo It enables/disables the terminal Local Echo.  Del to BS It enables/disables the delete command when pressing the Backs

DL TCL™ EXTENDED COMMANDS 45 4 4.3.3 Emulation 5250/3270 [Datalogic - SETUP Emulation 1) General 2) VT100/VT220 3) 3270/5250 ENTER to Continue Data

DL TCL™ 46 4  AS400 Printer It defines the parameters for the IBM AS400 printer. Unlikely the VT emulation, the AS400 emulation has no protocol st

DL TCL™ EXTENDED COMMANDS 47 4 4.4.1 Input / Output The Input submenu allows defining the data input through the keyboard or the scanner. [Datal

DL TCL™ 48 4 - Terminator key: defines the key to be pressed to include a terminator character in the output data format. Possible selections are:

DL TCL™ EXTENDED COMMANDS 49 4 4.4.2 Display The Display submenu allows defining the font dimension to be used for terminal emulation and the backl

DL TCL™ 50 4  Backlight The terminal Backlight is managed through the following parameters: - Auto: enables/disables the backlight each time a k

DL TCL™ EXTENDED COMMANDS 51 4 - Key Click: enables/disables a beep emission at any key press. - Beep: if selected, a further mask is displayed

DL TCL™ 52 4 4.7 FTP SERVER The FTP server is supported by each terminal and allows both the KC mode connection and file upload/download. When the

DL TCL™ EXTENDED COMMANDS 53 5 5 DL TCL™ EXTENDED COMMANDS 5.1 PROPRIETARY COMMANDS The proprietary commands allows exploiting standard features

iv 4.6 NEW Password... 51 4.7 FTP Server...

DL TCL™ 54 5 The following table lists commands managing different terminal functions: Function Command Change beeper frequency (<FFFFF>) and

TERMINAL ERROR MESSAGES 55 6 6 TERMINAL ERROR MESSAGES During the terminal normal functioning some error messages may appear on the display. The f

DL TCL™ 56 6 Error Message Description Parameters changed. Save changes? (Y/N) If exiting the main setup menu after changing some parameters, the t

GENERAL INFORMATION 1 1 1 GENERAL INFORMATION 1.1 DL TCL™ Datalogic Terminal Emulation Client (DL TCL™) is a software providing VT100, VT220 and

DL TCL™ 2 1 1.1.1 DL TCL™ Operating Modes DL TCL™ can be used for radio transmission with an Host or with a "Keep Connecting" PC which i

INSTALLATION 3 2 2 INSTALLATION 2.1 INSTALLING DL TCL™ ONTO THE TERMINAL Once the DL Mobile Configurator™ Enterprise 2 has been installed (see