Datalogic Hand-held devices II Spezifikationen PDF herunterladen (Seite 33)

PEN EMULATION



OPERATING MODE



MINIMUM OUTPUT PULSE



CONVERSION TO CODE 39



OVERFLOW



OUTPUT LEVEL



IDLE LEVEL



TO CHANGE THE DEFAULT VALUES

1. Read the Enter Configuration code ONCE, available at the top of each

page.

2. Read configuration codes from the desired groups.



= Default value

= Only for Enhanced Architecture readers

3. Read the Exit and Save Configuration code ONCE, available at the top of

each page.

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 132 133

HAND-HELD DEVICES 1
CONTENTS 5
HOW TO USE THIS MANUAL 8
1 INTRODUCTION 11
1.1 STATUS INDICATORS 12
2 INITIAL SETUP 13
3 CONFIGURATION 18
RS232 PARAMETERS 19
BAUD RATE 20
DATA BITS 21
STOP BITS 22
HANDSHAKING 22
ACK/NACK PROTOCOL 23
INTER-CHARACTER DELAY 24
RX TIMEOUT 24
SERIAL TRIGGER LOCK 25
WEDGE PARAMETERS 26
KEYBOARD NATIONALITY 27
CAPS LOCK 28
NUM LOCK 28
INTER-CODE DELAY 29
KEYBOARD SETTING 30
CONTROL CHARACTER EMULATION 32
PEN EMULATION 33
OPERATING MODE 34
MINIMUM OUTPUT PULSE 35
CONVERSION TO CODE 39 36
OVERFLOW 36
OUTPUT LEVEL 37
IDLE LEVEL 37
DATA FORMAT 38
CODE IDENTIFIER TABLE 39
CODE IDENTIFIER 41
CUSTOM CODE IDENTIFIER 42
TERMINATOR 44
FIELD ADJUSTMENT 45
FIELD ADJUSTMENT CHARACTER 46
CODE LENGTH TX 46
CHARACTER REPLACEMENT 47
POWER SAVE 49
ILLUMINATOR/LASER DRIVER 50
SLEEP STATE 50
ENTER SLEEP TIMEOUT 51
STANDBY 51
READING PARAMETERS 52
TRIGGER TYPE 53
TRIGGER SIGNAL 53
TRIGGER-OFF TIMEOUT 54
FLASH MODE 54
READS PER CYCLE 55
SAFETY TIME 55
BEEPER INTENSITY 56
BEEPER TONE 56
SOFTWARE FOCUS LEVEL 57
SOFTWARE FOCUS RANGE 58
DECODING PARAMETERS 59
INK SPREAD 60
OVERFLOW CONTROL 60
INTERDIGIT CONTROL 61
DECODING SAFETY 61
PUZZLE SOLVER™ 62
CODE SELECTION 63
EAN/UPC FAMILY 65
2/5 FAMILY 69
CODE 39 FAMILY 70
CODE 128 FAMILY 72
CODE 93 74
CODABAR FAMILY 75
CODABLOCK-A 77
CODABLOCK-F 77
PLESSEY 79
TELEPEN 80
DELTA IBM 81
CODE 11 82
CODE 16K 83
CODE 49 83
CONCATENATION 86
ADVANCED FORMATTING 100
4 REFERENCES 104
4.1.2 ACK/NACK Protocol 105
4.1.3 FIFO 105
4.1.4 RX Timeout 105
4.2 PEN PARAMETERS 106
4.2.1 Minimum Output Pulse 106
4.2.2 Overflow 106
REFERENCES 107
Output and Idle Levels 107
4.3 DATA FORMAT 108
4.4 POWER SAVE 111
4.4.3 Enter Sleep Timeout 111
4.5 READING PARAMETERS 112
4.5.1 Trigger Signal 112
4.5.2 Trigger-Off Timeout 112
4.5.3 Reads per Cycle 112
4.5.4 Safety Time 113
4.6 DECODING PARAMETERS 113
4.6.1 Ink-Spread 113
4.6.2 Overflow Control 113
4.6.3 Interdigit Control 113
Exit and Save configuration 116
SERIAL CONFIGURATION STRINGS 117
B CODE IDENTIFIER TABLE 127
C HEX AND NUMERIC TABLE 131
HEX / NUMERIC TABLE 132

Kommentare zu diesen Handbüchern

Keine Kommentare

Datalogic Hand-held devices II Spezifikationen Seite 33

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Barcodeleser Datalogic Hand-held devices II