Datalogic DS8100A-3115 Installationshandbuch PDF herunterladen (Seite 102)

DS8100A REFERENCE MANUAL

To run each instruction press the Next button. The procedure repeats the steps asking to

change the PCT-8000 X position (i.e. always before the PS Line (reference point) and

parallel to a conveyor edge but changing to the left-hand edge and/or to the center of the

conveyor), until the procedure terminates. At the end of the procedure, only the Stop

button is active. Typically 3 passes are necessary.

1 2 ... 97 98 99 100 101 102 103 104 105 106 107 ... 140 141

Reference Manual 1
CONTENTS 3
REFERENCES 6
COMPLIANCE 7
POWER SUPPLY 8
CE COMPLIANCE 8
FCC COMPLIANCE 9
GENERAL VIEW 10
GUIDE TO INSTALLATION 12
1 INTRODUCTION 15
DS8100A - X X X 17
1.5 INDICATORS 18
1.6 KEYPAD AND DISPLAY 19
1.6.1 Internal Net 19
1.6.2 Test Mode 19
1.6.3 PackTrack (Auto) 20
USING SCANNER MENU 21
PackTrack 22
1.7.3 Auto PackTrack Setup 23
INTRODUCTION 25
1.8 ACCESSORIES 26
2 INSTALLATION 28
2.2 MECHANICAL MOUNTING 29
2.2.1 Mounting the Scanner 29
M6 x 14 with flat washers 31
M6 x 12 with lock washers 31
2.3 POSITIONING THE SCANNER 32
CBX ELECTRICAL CONNECTIONS 33
3.1 POWER SUPPLY 35
3.2 MAIN SERIAL INTERFACE 35
Function 36
Multidrop Cable 39
Reference 40
USER INTERFACE 40
MEP-593 PH-1 Photocell (PNP) 42
9-pin male connector 48
25-pin male connector 48
4.1 POWER SUPPLY 51
4.2 MAIN SERIAL INTERFACE 51
4.2.1 RS232 Interface 52
DS8100A 53
4.3 AUXILIARY INTERFACE 56
4.4 INPUTS 56
EXTERNAL TRIGGER/ENCODER 57
4.4.1 Code Verifier 59
4.5 OUTPUTS 59
4.6 USER INTERFACE 61
5 LONWORKS CONNECTIONS 62
5.1 NETWORK TERMINATION 63
5.2 LONWORKS INTERFACE 64
LONWORKS CONNECTIONS 65
6 FIELDBUS CONNECTIONS 66
FIELDBUS CONNECTIONS 67
7 TYPICAL LAYOUTS 69
TYPICAL LAYOUTS 71
Minimum Distance 73
7.1.3 Redundant System 74
7.1.4 Multidata Network 76
7.1.5 Fieldbus Networks 77
8 SOFTWARE CONFIGURATION 79
Test Operating Mode 80
On Line Operating Mode 81
Automatic Operating Mode 81
SOFTWARE CONFIGURATION 83
Net-Autoset 84
Express Network Setup 84
Network Wizard 85
8.4 PARAMETER DEFAULT VALUES 90
9 READING FEATURES 95
Conveyor 96
Laser Beam 96
DS8100A REFERENCE MANUAL 100
Auto PackTrack Setup 101
READING FEATURES 103
Auto PackTrack Report 104
PackTrack™ Reference System 105
Ratio 3:1 109
9.4 READING DIAGRAMS 111
10 MAINTENANCE 121
11 TROUBLESHOOTING 123
12 TECHNICAL FEATURES 126
TECHNICAL FEATURES 127
A ALTERNATIVE LAYOUTS 128
Echo) (RS232) 129
PASS THROUGH 131
RS232 MASTER/SLAVE 132
MULTIPLEXER 134
GLOSSARY 135
DECLARATION OF CONFORMITY 140

Kommentare zu diesen Handbüchern

Keine Kommentare

Datalogic DS8100A-3115 Installationshandbuch Seite 102

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Barcodeleser Datalogic DS8100A-3115