Datalogic C-BOX 300 Installationshandbuch

DS4600AReference Manual

POWER SUPPLY - This product is intended to be installed by Qualified Personnel only. - Model DS4600A-XXX0: This device is intended to be suppli

GENERAL VIEW DS4600A DS4600A - 2XXX Models DS4600A - 3XXX Models 1 4235 678 10 1112 2 9 Figure A Cable with 25-pin ConnectorLaser Beam Out

GUIDE TO INSTALLATION The following can be used as a checklist to verify all of the steps necessary for complete installation of the DS4600A scanne

INTRODUCTION 1 1 INTRODUCTION 1.1 PRODUCT DESCRIPTION The DS4600A is a compact laser scanner complete with decoder designed and produced to be a fl

DS4600A 1 The DS4600A scanner uses a solid state laser diode as a light source; the light emitted has a wavelength between 630 and 680 nm. Refer to th

INTRODUCTION 1 1.2 MODEL DESCRIPTION The DS4600A scanner is available in versions that differ in regard to the following characteristics: • Decodin

DS4600A 2 2 INSTALLATION 2.1 PACKAGE CONTENTS Verify that the DS4600A reader and all the parts supplied with the equipment are present and intact w

INSTALLATION 2 2.2 MECHANICAL INSTALLATION DS4600A can be installed to operate in different positions. The four screw holes (M4 x 5) on the body of t

DS4600A 2 5.50.221154.5357.32.265.50.2210°5391.545.50.2230.125.50.2235°0.20 mm inchFigure 4 - Mounting Bracket Dimensions 6

INSTALLATION 2 2.3 ELECTRICAL CONNECTIONS DS4600A is equipped with a cable terminated by a 25-pin D-sub connector for connection to the power supply

DS4600A 2 2.3.1 Power Supply Power can be supplied to the scanner through the pins provided on the 25-pin connector used for communication with the h

INSTALLATION 2 2.3.2 Main Serial Interface The signals relative to the following serial interface types are available on the input/output connector

DS4600A 2 The RTS232 and CTS232 signals control data transmission and synchronize the connected devices. Figure 9 - RS232 Control Signals If the

INSTALLATION 2 DS4600A USER INTERFACE7 SGND MainTX485+ 2TX485- 4RX485+ 3RX485- 5RX485TX485RS485REFEarth Ground Figure 10 - RS485 Full-Duplex Connecti

DS4600A 2 The figure below shows a multidrop configuration with DS4600A scanners connected to a Multiplexer. 1 1 CHASSIS# 1 RTX485+ RTX485- SGND Ma

INSTALLATION 2 20 mA Current Loop (C-Box 100 w/INT-30 Accessory Only) To adapt DS4600A to 20 mA current loop interfaces, it must be connected to a C

DS4600A 2 2.3.4 Inputs There is an input available on the DS4600A scanner relative to the External Trigger. There are also 2 general purpose inputs:

INSTALLATION 2 18/6/14 +19/10/15 - USER INTERFACEDS4600A Signal+ 5V VS925GNDGroundV Figure 15 - Input NPN Command Using DS4600A Power

DS4600A 2 The electrical features of the inputs are: Maximum voltage = 30 Vdc Maximum current = 25 mA. An anti-disturbance hardware filter is implem

INSTALLATION 2 2.4 USER INTERFACE RS232 PC-side connections 1 5 9 6 9-pin male connector 13 25 141 25-pin male connector Pin Name Pin Name 2

DS4600A REFERENCE MANUAL

DS4600A 2 2.5 POSITIONING The DS4600A scanner is able to decode moving barcode labels at a variety of angles, however significant angular distortion

INSTALLATION 2 The Tilt angle is represented by the value T in Figure 21. Position the reader in order to minimize the Tilt angle. TFigure 21 - Til

DS4600A 2 2.6.1 Point-to-Point In this layout the data is transmitted to the Host on the main serial interface. Host Mode programming can be accompli

INSTALLATION 2 2.6.2 Pass Through Pass through mode allows two or more devices to be connected to a single external serial interface. Each DS4600A t

DS4600A 2 2.6.3 RS232 Master/Slave The RS232 master/slave connection is used to collect data from several scanners to build either a multi-point or a

INSTALLATION 2 2.6.4 RS485 Master/Slave The RS485 master/slave connection is used to collect data from several scanners to build a multi-point or a m

DS4600A 2 2.6.5 Multiplexer Each scanner is connected to a Multiplexer (for example MX4000) with the RS485 half duplex main interface. c Main Seria

READING FEATURES 3 3 READING FEATURES 3.1 ADVANCED CODE RECONSTRUCTION The traditional way of barcode reading could be called "Linear Reading

DS4600A 3 3.1.1 Tilt Angle for Advanced Code Reconstruction The most important parameter in Advanced Code Reconstruction is the value of the maximum

READING FEATURES 3 3.2 DECODING CAPACITY IN LINEAR MODE When in Linear Reading mode, the number of reads performed by the DS4600A and therefore the

DATALOGIC S.p.A. Via Candini 2 40012 – Lippo di Calderara di Reno Bologna - Italy DS4600A Reference Manual Ed.: 04/2006 A

DS4600A 3 If scanning is perpendicular to the direction of the code movement (Figure 31), the number of effective scans performed by the reader is giv

READING FEATURES 3 If scanning is parallel to the code movement (Figure 32) the number of effective scans is given by: SN = [((FW-LW)/LS) * SS] - 2

DS4600A 3 The reading characteristics for the raster versions are given in the table below. The distance between the top and bottom scan lines is give

READING FEATURES 3 3.4 READING DIAGRAMS The following diagrams show the reading distance for barcodes with different densities. DS4600A-210X (Long R

DS4600A 3 DS4600A-200X (Medium Range) 4 2 0 -2 10 8 6 -4 -6 (in) 02 64 12(in) 810 141618050 100 150 200 250 300 350 400 450 500 550(mm) 250200150100

READING FEATURES 3 DS4600A-22XX (Short Range) 2 1 0 -1 5 4 3 -2 -3 -4 -5 (in) 01 3 2 106(in) 45 7 8 9020 40 60 80 100 120140160180200220240260(mm) 1

DS4600A 3 DS4600A-22XX (Short Range) 4 2 0 -2 10 8 6 -4 -6 -8 -10 (in) 02 64 2012(in) 810 141618040 80 120 160200 240280 320360400440480520 (mm) 240

READING FEATURES 3 DS4600A-2X1X (Raster R1) 4 2 0 -2 10 8 6 -4 -6 (in) 0 2 64 12(in) 810 1416180 50 100 150 200 250 300 350 400 450 500 550(mm)250

DS4600A 3 DS4600A-2X2X (Raster R2) 4 2 0 -2 10 8 6 -4 -6 (in) 0 2 64 12(in) 810 1416180 50 100 150 200 250 300 350 400 450 500 550(mm)250 200 150 1

READING FEATURES 3 DS4600A-31XX (Long Range) 4 -4 12 -12 -16 (in) 0 4 2012(in) 8 160 100 200 300 400 500 600 700 800 900 1000(mm) 400 300 200 100 0-

CONTENTS REFERENCES ... v Conventions...

DS4600A 3 DS4600A-30XX (Medium Range) 4 2 0 -2 10 8 6 -4 -6 (in) 02 64 12(in) 810 141618050 100 150 200 250 300 350 400 450 500 550(mm) 250200150100

READING FEATURES 3 DS4600A-32XX (Short Range) 4 2 0 -2 10 8 6 -4 -6 -8 -10 (in) 02 64 2012(in) 810 141618040 80 120 160200 240280 320360400440480520

DS4600A 4 4 MAINTENANCE 4.1 CLEANING Clean the laser beam output window periodically for continued correct operation of the reader. Dust, dirt, et

TROUBLESHOOTING 5 5 TROUBLESHOOTING 5.1 GENERAL GUIDELINES When wiring the device, pay careful attention to the pin number of the signals and wheth

DS4600A 5 TROUBLESHOOTING GUIDE Problem Suggestions Power On: the “Power On”/”Ready” LED is not lit Is power connected? If using a power adapter (lik

TROUBLESHOOTING 5 TROUBLESHOOTING GUIDE Problem Suggestions Reading: Not possible to read the target barcode (always returns No Read) Check synchron

DS4600A 6 6 TECHNICAL FEATURES ELECTRICAL FEATURES DS4600A-XXX0 DS4600A0-2XX5 Power Supply Voltage 10 to 30 Vdc 24 Vdc Power Consumption max.

TECHNICAL FEATURES 6 SOFTWARE FEATURES READABLE CODE SYMBOLOGIES • EAN/UPC • Code 93 • 2/5 Interleaved • Code 128 • Code 39 • EAN 128 • C

GLOSSARY Advanced Code Reconstruction The Advanced Code Reconstruction technology allows reconstructing and reading damaged or very tilted barcodes

Decoder As part of a barcode reading system, the electronic package which receives the signals from the scanner, performs the algorithm to interpret

3 READING FEATURES ... 25 3.1 Advanced Code Reconstruction...

Picket-Fence Orientation When the barcode’s bars are positioned vertically on the product, causing them to appear as a picket fence. The first bar wi

Skew Rotation about the Y-axis. Rotational deviation from correct horizontal and vertical orientation; may apply to single character, line or entire

INDEX A Accessories; 3 Advanced Code Reconstruction; 25 C Cleaning; 40 E Electrical Connections; 7 G General View; ix Glossary; 46 Guide to Insta

DATALOGIC S.p.A., Via Candini, 2 40012 - Lippo di Calderara Bologna - Italy 05 dichiara che declares that the déclare que le bescheinigt, daß das

REFERENCES CONVENTIONS This manual uses the following conventions: “User” or “Operator” refers to anyone using a DS4600A. “Device” refers to the D

SAFETY REGULATIONS LASER SAFETY The following information is provided to comply with the rules imposed by international authorities and refers to

AVOID EXPOSURE LASER LIGHT IS EMITTED FROM THIS APERTURE CAUTION-CLASS 3BLASER LIGHT WHEN OPEN AVOID EXPOSURE TO BEAM DATALOGIC S.p.A. Via Candini, 2