STAR-Box™Installation Manual
viiiSAFETY PRECAUTIONSPOWER SUPPLYAttention: read this information before installing the product.- This product is intended to be installed by Qualifi
GENERAL FEATURES111 GENERAL FEATURES1.1 DESCRIPTIONThe STAR-Box™ is a STAR-SYSTEM™ accessory used as a connection boxbetween STARGATE™ devices and the
STAR-BOX™222 INSTALLATION2.1 PACKAGE CONTENTSVerify that the STAR-Box™ and all the parts supplied with the equipment are presentand intact when openin
INSTALLATION322.2 OPENING THE DEVICETo install the STAR-Box™ it is necessary to open it by unscrewing the four coverscrews shown in Figure A.CAUTIONT
STAR-BOX™422.3 MECHANICAL INSTALLATIONThe diagram below gives the overall dimensions of the STAR-Box™ and may beused for its installation.∅ ∅ mminFi
INSTALLATION52STAR-Box™ can be installed by physically mounting it to a wall or panel using eitherthe adhesive strips or screws and dowels provided. T
STAR-BOX™622.4 ELECTRICAL CONNECTIONSThe following STAR-Box™ typical layouts are shown. The RS485 cables in thefigures are shielded with 2 twisted-pai
INSTALLATION72Figure 6 - Repeater- Network LayoutA = Host PC C = Passive STAR-Box™B = Active STAR-Box™ Converter D = Power SupplyE = Active STAR-Box™
STAR-BOX™822.4.1 PinoutThe STAR-Box™ spring clamp connector pinouts are indicated in the following table.1 RS485+2 RS485-3VS4GNDS1RS4855 Shield6 RS485
INSTALLATION92Example: The values in the table refer to a system composed of 1 active STAR-Box™ and N passive STAR-Boxes™ with their STARGATE™ basesta
STAR-Box™Installation Manual
STAR-BOX™1022.4.3 RS485 Half-Duplex BusThe RS485 half-duplex bus signals are supplied to the STAR-Box™ through the pinsprovided on the spring clamp c
INSTALLATION112Figure 10 - System cable connectionsThe wiring used can be solid or stranded but must meet the following specifications.All positions:
STAR-BOX™122Figure 11 - Connection Jumper SettingsThe STAR-Box™ passive models also allow connection to an F904/N Converter.2.5.2 RS485 Bus Terminati
INSTALLATION1322.5.3 LED IndicatorsFigure 13 - LED IndicatorsThe two internal LEDs indicate the following:POWER ON(red) indicates the STAR-Box™ is con
STAR-BOX™142Figure 14 - Connection Jumper Settings2.6.2 RS485 Bus TerminationConverter Mode: In this case STAR-Box™ is connected to the Host and ther
INSTALLATION1522.6.3 Converter/Repeater SelectionSTAR-Box™ active models are used either in Converter Mode to connect the RS485bus to an RS232 port on
STAR-BOX™1622.6.5 LED IndicatorsFigure 18 - LED IndicatorsThe three internal LEDs indicate the following:POWER ON(red) indicates the STAR-Box™ is conn
TECHNICAL FEAURES1733 TECHNICAL FEATURESActive PassiveELECTRICAL FEATURESPowerSupply voltage 9 to 30 VdcPower consumption max. 270 mW +STARGATE™135 m
02DATALOGIC S.p.A.,Via Candini, 240012 - Lippo di CalderaraBologna - Italydichiara chedeclares that thedéclare que lebescheinigt, daß das Gerätdeclar
STAR-Box™INSTALLATION MANUAL
DATALOGIC S.p.A.Via Candini 240012 - Lippo di Calderara di RenoBologna - ItalySTAR-Box™Ed.: 04/2002ALL RIGHTS RESERVEDDatalogic S.p.A. reserves the ri
iiiCONTENTS1 GENERAL FEATURES ... 11.1 Description...
ivGUIDE TO INSTALLATIONThe following can be used as a checklist to verify all of the steps necessary forcomplete installation of the STAR-Box™.1) Rea
vGENERAL VIEWSTAR-Box™Figure ARJ45 RS232/RS485 connectorCover screws (4)Compression connectors123123
viSTAR-Box™1063 4215987Figure B - Active STAR-Box™ Internal ViewRS485 line w/ power connectors12RS485 line w/ power connectors3Power connectors54Power
viiSTAR-Box™83421756Figure C - Passive STAR-Box™ Internal ViewRS485 line w/ power connectors12RS485 line w/ power connectors3Power connectors54Power o
Kommentare zu diesen Handbüchern